Announcement

Collapse

ONE RULE

Consider this your neighborhood bar,corner soap box, fish house, marina, coffee shop or anywhere else you go to hang out with friends and talk anything you want. Only thing, personal attacks will not be tolerated. No name calling or belittling. Be civil at all times and have fun. If a topic offends you, don't read any further.
See more
See less

Old Nasty Black Adhesive in Rub Rail Staining Hull

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • GREGK
    replied
    Got them black streaks on my gelding too. Used Mothers Marine Black Streak Remover. Then l stripped all the wax off using white vinegar. Wash hull with dawn after, rinsed really really good then used a new fangled ceramic coatings l got from work for cars. Don’t remember the name but there are products out there for gelcoat. Used boat for two years in salt and 3 years sitting on the hard.. The streaks would wash right off with a fiberglass soap and water with very little effort. I sold the boat the 6th year in the spring, washed it before l put her up for sale, could see it needed to be redone by the 5th year but she cleaned up well.
    Was told the streaks come from oxidation between the different materials under the rub rail. So l don’t think sealing would be a good idea. But that is just my .02$

    Leave a comment:


  • crhodes
    commented on 's reply
    Agree. Might add 1) cut old sealant away if protruding below the rub rail (as shown in picture an 2) after cleaning, wipe down with acetone to get all residual oils off, then use the caulk.

  • Pedlyr
    replied
    That looks something like Sikaflex which is a great sealant but cant take UV. Or maybe something else. Might just be easier to remove sealant as mentioned and redo.

    Leave a comment:


  • Quik Fix
    replied
    I don't believe the factory used adhesive. Rub rail was screwed thru the cap and hull into a thin wood backing. The wood doesn't last very long. If you could find out what the adhesive is, it would be easier to eliminate it.

    Leave a comment:


  • holty
    replied
    After scrubbing with a strong detergent and a rub down with lacquer thinner I would run a thin bead of a sealant of your choice where the rail meets the hull. After the sealant is set give the rail two or three coats of your favorite wax.

    regards Holty

    Leave a comment:


  • Damon
    started a topic Old Nasty Black Adhesive in Rub Rail Staining Hull

    Old Nasty Black Adhesive in Rub Rail Staining Hull

    Greetings!

    The factory black adhesive under the rub rail has been staining my hull for a while now (10 plus years):

    Click image for larger version  Name:	rubrail1.jpg Views:	0 Size:	72.1 KB ID:	33672

    Click image for larger version  Name:	rubrail2.jpg Views:	0 Size:	52.4 KB ID:	33673

    Click image for larger version  Name:	image3.jpg Views:	0 Size:	52.7 KB ID:	33675

    When I had the boat out during my repower in 2019, I scrubbed the black adhesive to get the surface as clean I could to where it was not staining my finger when I ran it on the surface. But after some time, it started back up.

    The boat will be blocked up at the boat yard for a new coat of anti fouling paint next week, so I would like to address this the best I can without removing the rub rail. Any ideas on how to do this? I noticed that some of the black adhesive has come off already:

    Click image for larger version  Name:	image4.jpg Views:	0 Size:	47.8 KB ID:	33674

    Thank you, and happy holidays!
    Attached Files
    Last edited by Damon; 12-24-2021, 10:42 AM.
Working...
X